Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
I am trying to build a project with Visual Studio Code that uses MCUBoot. I have created a new project based off of the "Hello World" sample, which runs on my nrf52840 without...
Hello,
I have created different characteristics with the CCC macro (BT_GATT_CCC) that share the same "Configuration changed callback" function.
Inside the function below...
Hi,
I am using the download client library (MFW 1.1.4 due to Verizon compatibility) and am noticing that the TLS handshake with my server only succeeds after the first few...
Hi,
I am trying to build the bluetooth sample peripheral_lbs from the nrfconnect sdk. I get the following errors:
/home/newtrax/workspace/sdk-nrf/samples/bluetooth/peripheral_lbs...
How can i use the nRFConnect to read recognized gestures (idle, updown, rotate and tap) from the machine_learning application?
Tried to do this, but no services broadcast...
Hi,
When receiving BLE packets from another peer via different channels - in which stage does the peer understand if the packet belongs to him, or it's just a packet which...
Hello Nordic Team,
I need your help ! I have developed an App for nRF Connect for Desktop to be able to read and write UICR on device using nRF52 Series chips. It was working...
Dear Members,
I read about interrupt vector on S332_SDS_v2.0 page 78, 17.1.1 Interrupt forwarding to the application
=====
For the SoftDevice to locate the application...
Module NRF52832
Sdk: 15.2
I am trying to debug the module on a custom board, debugging worked fine until something weird happened on the specific board...
After the...
Hi,
I have nrf52840 DK connected to PC.
I have nRF5 SDK v17.0.2 installed.
I wanted to try out ble_app_blinky_pca100056_s140 example from the SDK, using Segger Embedded...
Hi,
Is there any example I can see to get I2C working in Zephyr on the NRF52832? Really would need help with this. Ultimately I need to get an accelerometer working within...
Hello,
I'd like to separate mcuboot code from keys and implement a strategy described on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/mcuboot/design...
