S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
I'm building a COAP client using the Nordic nRF9160DK cloud coap-client example code as my base. I have the UDP version working great. But I'd like to convert to TCP.. I was...
Hi all, I have an odd issue with an iphone XR. The NRF Connect for Mobile application can see adverts from the device when scanning, but the device does not appear in the...
Hey! I'm trying to sniff the data moving between a Bluetooth LE button and a Central.
Installation of the Bluetooth LE Sniffer went pretty smoothly but Wireshark only shows...
Hi,
I'm trying to use a nrf delay to make a delay for a motor. The idea is to make the motor oscillated by putting it forward and then reverse via a delay. (you can find...
Hello,
I need to run "west build" and "west flash" commands from my custom IDE/Editor. If I open up Toolchain Manager and then do "Open bash" or "Open Command Prompt", ...
Hello,
I am trying to do directed advertising while us ing the coded PHY whithout bonding the devices but i am running into some problems.
The device with the BT-address...
Hi,
I use nRF5340DK (0.11.0) as HCI controller and noticed it can randomly (?) accept PDUs with access address other than configured. This basically makes it impossible...
Hi,
When I build CLI sample in nRF_Connect_SDK, I don't get any USB port for CLI.
I believe the sample is in default mode built for UART.
How to build this for USB,...
Hello. I can't normally use USB for two-way communication.
The problem is sending the PRX payload in ACK packets.
After conducting a simple test: PPTX sends a packet once...
Trying to use the basic baremetal mode as my application is very simple and dont want to go through RTOS stuff.
I tried with Timer and RTC, both case if I enable the interrupt...
Dear Nordic Team,
I was trying to use the I2C peripheral on the nRF5340 with clock speed of 1MHz, but I kept getting the error "unsupported speed". I was using the function...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
I am using the nRF 52840dk board and I am new to nRF, I had worked on Cypress CYBLE & CYBT-343026-01. I am starting my development for basic BLE transmit, eventually, I am...
Dear Nordic experts, How do you verify that a (mesh) firmware has an app key assigned? What I'm looking for is basically the Mesh SDK's version of NCS's bt_mesh_app_key_exists...
I used the alternate method of installing nRF connect described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrf/gs_installing.html#build-environment...
