We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
Hi,
I have the following 2 scenarios:
Scenario 1: I create an image with nrfutil containing SD, App and debug bootloader. I flash this image and it works. Then I change...
We have nrf5340pdk kit we are trying to flash code via nrf connect or Segger studio but firmware is not flash and when we powered up the pdk it's showing three port can you...
I'm using Visual Studio 1.7.1 on Windows 10 machine. With an nrf916DK.
I'm trying to learn about the shell and all seems to be working fine, based on what I've found in...
I'm trying to work with Kismet's nrf51822 plugin that would allow kismet to read the nRF BLE sniffer 4.1.0 the same way Wireshark does. Alas, theirs is C based and I don't...
Dear friend,
Based on the following conditions: SDK: 15.3 Target board: nRF52840-DK Example: \examples\ble_peripheral\ble_app_ancs_c ios version: 12.5.5 Do the following...
Hello,
I have successfully achieved the modem delta firmware update from mfw_nrf9160_1.2.7 to mfw_nrf9160_1.2.7-FOTA-TEST, vice-versa with sample code. But when it comes...
Dear support
Just started to learning following the tutorial here - https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-3-0#h769sk6kqovea15p99jn16lstat1dtpuuw...
Recently I purchased nRF9160 DK and I have a Vodafone Idea SIM (active). I followed the instructions precisely as per the Nordic infocenter but I am not able to connect my...
Hello
nRF52840 is easy to know pin number,
but nRF5340 no pin map,i can't read the pin diagram.
don't know where the pin corresponds to.
thanks
Best R...
Hi,
I managed to have the fat_fs sample to work.
Now i would like to be able to write and read files, onto the SD-CARD, that a PC will understand, it seems to needs...
Hello all,
I am developing on the nrf52 dk. and the following type definitions should be defined according to the given library.
Would somebody please comment if that...
