We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
the updated version of nRF connect v3.8 , for desktop , app - programmer doesnt recognize the device . i downgraded to 3.3v this version selects my device .
Hello,
I have developed a Thread network based on SDK for Thread & Zigbee v.4.1.0 and OTBR image provided by Nordic. I recently upgraded my OTBR from a Raspberry Pi 3B+...
Hi, I have added libuarte example in-app template and sent data from Arduino to nRF52840 successfully. But after receiving some data and I am getting the following error....
Hi,
I use nrf5340 and have issue with i2c large buffer send: In order to flash page to bootloader with my application:
I defined
I defined static array with size...
Hello !
If I understand right and nrf_crypto is the main Crypto API in nRF SDK. They can be mapped to cc310 or to mbedtls sw routines.
Does exists nrf_crypto asynchronous...
Hi,
When I try to run a colleague's project on my PC in debug mode in Visual Studio Code, I get the error "Run to 'main' timed out. Trying to pause program":
The debug...
Hello, guys.
We have nRF51822 SoC with 256KB of Flash and 32KB of RAM memories at our disposal. For our application, we would need to use the BLE stack + over-the-air DFU...
Hello,
I have gone through many devzone threads which suggest that Ble Mesh over coded PHY is not officially supported but, is possible. I am trying out the "Mesh" sample...
Hello! I recently dived into using the nRF52840 SDK + Zephyr the goal is to use this for Bluetooth Long Range Extended Advertising. Are there available tutorials, resources...
Hello,
I am using sdk12,2.2 and nrf52832. I have interfaced bme680 sensor with nrf52. I am facing strange challenge.
My button interrupt is working every time but it stops...
Hi, I am working on nRF52811 as central and I want to put the device in full power save mode so it does not consume power and activate once I pressed the button. How can I...
Dear Sirs,
I am evaluating the option of controlling a couple of motors (each with an independent controller based on a nRF52840 device) from a Smartphone App. Both controllers...
Hello!
I have a problem where visual studio code is really unstable with detecting the nRF52DK nRF52832 in the connected devices tab. After setting up the IDE and SDK it...
Hi,
Im using an nRF5340 on the peripheral. Now i would like to use a Dongle on the PC-side, what device can you recommend?
nRF52840 Dongle ? Or is there an other dongle...
Hi, I'm using the serial_lte_modem sample application and I've modified the AT#XMQTTPUB command so that I can specify a slot number from which the device can grab a bank of...
