Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
Hi, I use two nRF52840 DK for testing purposes for over 1.5 years now. Suddenly, yesterday the BLE module in one of the DK's stopped working. Just like that. Same functional...
Hellow
We are in trouble. Please tell me what to do.
The input range of the SAADC is not as expected.
I use: ・nrf52840 ・VDD=3.3V by Regulator ・nRF5_SDK_17.1.0 ・Sample...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
The example ble_app_uart is working fine (i.e. I get NRF_LOG_INFO from gatt_evt_handler), but my code doesn't. I've checked the diff between them and tried adding all diffs...
Hi All,
I am using nRF52 DK board & nRF5_SDK_17.1.0 for Development(Emulated Project for nRF52805), My application needs creation of multiple service and multiple characteristics...
I bought a handful of nrf52840-Dongle boards, with the intention of developing an application on one "dev" board and then flashing it through the Open Bootloader on the others...
hi am working on DFU- OTA on nRF52833. In one of the query I found the method for to evaluate DFU- OTA on nRf52833 , am able to do that ,after connected to the Bluetooth I...
Hello,
I am new to Nordic. Earlier I was using Cypress controllers CYBT343026-01. As per nRF documentation, I believe once the controller goes into a deep sleep mode, I...
Hello,
I am trying to port a project from the NRF52840 DK to a custom board where I am using the NRF52820. The code compiles fine when the project is using the settings...
Hi, devzone!
I'm trying to use a timer to periodically change the digital output but it seems that the handler function is not called.
The whole code is based on the...
Hello!
For a project, I am relying on RSSI data from the development kit nRF52832. The problem is that the data I get is in dBm (I assume?), that is values like -30, -50...
Hi,
We are designing a board that is controlled by a NRF52840 and that will use a NRF21540 (FEM) to enhance its radio link budget.
We will use the FEM with diversity antenna...
Hi,
The DFU(reuse ota code) partition configuration file I got from your technical support is as follows,It divides Flash（1024K） into the following regions：mcuboot(48K)...
Hi, I need to use UART0, UART1 and I2C0 in my application. I initialized these in overlay file (attached). When, debug is run, it is observed that the I2C binding is not successful...
