Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm testing a simple application based on the UDP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi,
My custom board using nRF52810, project was based on ble_app_uart_pca10040e_s112 and secure bootloader.
The size of application is 59k, and the bootloader is 32k....
Hi
I looked in the nRF9160_PS_v2.0.pdf，I can not find the voltage level of SPI signal pins，Does the voltage level of SPI signal pins equal to the voltage supply to the VDD_GPIO...
Hello,
I am using SES environment with nRF Connect SDK 1.9, SoftDevice S140 and nRF5_SDK_17.1.0 to clone the nrf52-ble-multi-link-multi-role example on Github ( https:/...
I'm facing some issues over connecting over to AWS with a custom board, the board was connecting before and the code connects with AWS using a Thingy91
Hi,
I'm trying to develop a simple application on the NRF5840 DK using the NRFConnect SDK inside VScode. I am struggling to see how to add external libraries to an application...
Hello,
I am using the nRF 52840 DK board. I am trying to implement the code for the HX711 in Zephyr.
I was just comparing the code with Arduino which I have written and...
Good Day.
I plan to use nrf52840 in my development, but at the moment this microcontroller is not on sale. But there is an nrf52840-Dongle on sale.
Can you please tell...
Hello,nrf_pwr_mgmt
I am doing basic BLE advertising on the nRF52840 DK board and using nRF5 SK 17.0.2. I can see the current consumption is ~50uA but after using nrf_pwr_mgmt...
So I have been wanting a opensource gaming mouse for a long time, and gwolves decided to make one recently using a nRF52840 (you can learn more here ). Only issue is that...
I built the project on VS CODE, but it failed at the beginning
log output:
> Executing task: nRF Connect: Generate config nrf52840dk_nrf52840 for f:\nordic-sdk\project...
Hi, I've made custom boards using nrf52840. In my application I did advertise forever with interval of 200ms. Now after several weeks of tests I've two boards out of seven...
Goodday
I thought I would try the webinar
️ nRF Connect for VS Code Webinar - Hackster.io
Im getting the following error after I add Build configuration
Building...
After installing NCS 1.9.0 Open Segger Embedded Studio does not show as an option any longer. I have tried to remove the SDK and install it again, but the result is the same...
Can distance be set between nRF52840 and APP? For example, set 5m and 10m through app. When the distance between nRF52840 and APP exceeds the set distance, app will remind...
