Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
There have been several releases to both the Command Line Tools and Segger's JLink Software however the full Nordic toolchain still does not properly support the M1.
In...
Hi Nordic! I'm using the nrf ftp client library found here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/ftp_client.html I'm having...
Hi,
I have a nRF52833 DK which I'm evaluating for a new product which uses a UART connected GPS receiver.
I found some simple UART code which compiles OK, but crashes...
Hello, guys.
We are using nRF51822 SoC and Zephyr OS to develop our application.
I wonder if it will be possible to use Nordic's Button Handler module in the Zephyr environment...
Good afternoon,
I am working with the Thingy:91 platform and I would like to know if it is possible to get the GPS position without internet connection and if there is any...
Hi Team
1. are the following phy layer parameter like SNR,RSSI available for both WIFI and BLE?
2. if so, which register to look for such information
3. Also how about...
Hello
I am getting started on nRF SDK and I went through all the examples (at least those I'm interested about) successfully.
Now, I need to merge couple of examples together...
Hey
When i disconnect my nRF5340-DK devkit to my Lenovo T14s Gen 2 running Ubuntu 20.04.3 LTS the usb driver in the linux kernel crashes.
I think it's a problem that...
Hello there,
I've set up a Thread network with a few devices, and now I would like to connect to a ipv4 server.
At home or at the office we do not have a ipv6 public address...
Hi,
We are Migrating from nRF52832 to nRF5340 dual-core soc. In nRF52832 9 off available GPIOs were only to use with a low drive, low-frequency application since they may...
Hello,
Every time I try to run the sample gnss in SDK 1.8, I got this error gnss_sample: Failed to generate JWT, error: -8
Please can you let me what this error means...
I have starting working with UART. I see that there are two options for configuring it: UART_0_ASYNC and UART_0_INTERRUPT_DRIVEN. I want to use ASYNC option for my UART, but...
Hello
NCS1.8.0 Windows10 X64;
Can [v1.8.0\zephyr\tests\drivers\adc] convert microphone analog signal into digital signal? for I2S 8bit 8kHz
thanks
Best Regard...
I am tying to match the nRF52840 rf output to my 50 ohm 2.45GHz pcb antenna. What is the optimum rf impedance for best transmitter/receiver performance? The markings on the...
Hi, I need to fetch the Device ID of nRF5340 Chip. In datasheet Info.DeviceID[n], n = 0...1 , is mentioned. How to access this information ? Also, I am using nTF5340-DK kit...
