Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi, I'm trying to implement a timer that will trigger each 10ms (for example) an handler function and do something inside it. So, I came with the idea to implement an App...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi everybody!
I'm starting to study nrf9160. Work in SEEGER Embedded Studio. And I immediately had a question:
By default, it is created C project, But I want to create...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
Hello Everybody,
If you're reading this, you're likely in the same boat as me and need to scale Nordic's build process in an environment that doesn't have access to west...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hello,
I am creating this ticket in continuation with Case ID: 278810 as my doubts are not cleared yet. I need your support to get them clarified asap as we need to prepare...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
