Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hello, I recently picked up a nRF PPK2 and I'm liking it a lot.
I have it wired in-line with a battery (1500mAh li-po) with my device under under test. Measuring battery...
Hi,
I am using nRF52805 to transmit string data to the mobile end app "nRF Connect".
I found that sometimes the app will display hex data instead of the expected decimal...
I'm using the logger (LOG_INF, LOG)_DBG...etc) to print out debug messages. I'd like to have timestamp printed out. Right now it looks like this: D: xxxx or I: xxxxx
I found...
Hello, I am working with 2 nRF52840 dk's and a Conbee ii.
The DK's are using nRF5 SDK for Thread and Zigbee 4.1.0.
DK 1 is running the CLI example.
DK 2 is running...
Hi, I want to integrate DWM3000 with with nrf9160. To begin with, I need a simple SPI example which I can't seem to find in the nRF connect SDK. There is an unofficial example...
I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). I'm trying to connect to a test mqtt broker (mosquitto) using AT commands via LTE...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hello,
I successfully merge example libuarte and ble_app_beacon and built .
My problem started after it receive 48 bytes of data from sensor via uart ,This is my area...
I want to enable GPIO IRQ in Trusted firmware-m 1.3 on nrf5340DK. I have TFM 1.3 which comes with zephyr v2.7.0 image flashed to board. followed the steps of https://www.trustedfirmware...
Hello,
I am trying to protect the battery on our application by putting my device in DEEP_SLEEP_! mode when a certain voltage is reached and waking it up upon a GPIO input...
Hello, i would like to know if this is possible to send less than 20bytes per packets, by changing the parameters like BLE_GATT_ATT_MTU_DEFAULT or the max data len. My goal...
Hello,
I'm trying to evaluate the Thingy:91 on Nb-IoT networks. I'm currently in the Philadelphia suburbs. I'm using the iBasis SIM card which was packaged with the device...
We like to use nrf9160 and we tried to find operator in India who sells NB-IoT / LTE-M sim card. but unable to find. Is there any operator providing NB-IoT / LTE-M enabled...
Dear Forum,
Im using a NRF52840dk connected to a NRF9160dk with the SLM application running.
Sending uart data from the 52840 to the modem works and modem gives a response...
