Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hello,
We are attempting to abstract the FOTA service within our custom...
nRF SDK Version 16.0.0 nRF52840 iOS version 15.2 I'm having an issue with my iPhone displaying incorrect characteristic data after doing a DFU to my nRF device, re-connecting...
Hello,
I am trying to set up the IDE extentions in VScode. When I try to connect my thingy91 it doesn't show up in the connected devices window. When I connect my nRF52832...
i am trying to develop a monitoring system for musician and low latency audio streaming is key!. preferable below 10ms i would wat to at least stream cd quality audio 128kbps...
Hi,
I am using LIBUARTE on our custom board. The UARTE is talking to a device which may temporarily be powered-down while the system is in low-power state.
Two questions...
Hello,
I have used VS Code for nRF Zephy and in that, I can import (example code)/write code in Zephyr. But is it possible to import Softdevice (nRF5_SDK_17.0.2_d674dde...
Hi all,
i am working on nrf5340 device (sdk v1.5.1)which is connected to microphone.Audio recorded in mic is transmitted via USB to PC(testing on PC right now).while device...
Hi,
I am looking connect some sensors (links below) to the nrf9160dk and send their data over cellular to the nrfcloud.
Water temperature sensor: Waterproof DS18B20 Digital...
Hello all
I am facing a very strange issue, already searched the forum but didnt find anything like it.
Okay so I can get DFU to work. For our custom application we have...
Hi,
I am trying to interface WM8960 CODEC with nRF52832 using (I2S and I2C) .
I am able to communicate with IC with TWI
I want to transmit the const uint16_t wavedata...
Working on a project where I need some sort of wireless communication. The device is located inside a metal enclosure, so IR is not an option. Its only goiong to trigger a...
Hello, I'm using an nRF5340 board with nRF Connect SDK as a BLE peripheral device, and I'm trying to get RSSI value when another device connects to it.
So I'm trying to...
I am attempting to enable the external LFCLK. I want the clock to swing rail to rail. I have the following code in place. I am using the s140 v 7.2 soft device and the nRF5_SDK_17...
We are using nrf52832 soc for our product development and using that we are trying to increase the throughput of our device using the information from the following forum...
