Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
Hi support,
I'm currently having issue trying to program a nrf52833 device using Jlink mini on mac. I have no problem programming the device using a pro Jlink on windows...
Hi,
I'm trying to use examples. The ICM42605 example does not work.
I get the following errors.
There seems to be an error in the code below.
It was tested with...
Hello !
I have found that error free decryption ( MIC error) on fly depends from S1LEN configuration value.
S1LEN have valid range value for each radio mode
2Mbit 1...
I'm getting an occasional NRF_LIBUARTE_ASYNC_EVT_OVERRUN_ERROR, it often takes over 24 hours to reproduce, and the libuarte appears to be generating garbage after the error...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
Hi,
Since adding a custom board to a app from a sample, the Flash button:
Has stopped working properly.
When i press it, a build is initiated, but the flash does not...
Hi,
I used this example to develop code for a low power delay function. This code uses RTC1 with frequency = 32Hz to create an interrupt every 5 seconds and event handler...
Hi,
I have been programming my custom board using SWD on a DK. It worked fine when I tried blinky example, however, when I tried nrf_ble_uart example, it stopped at the...
The documentation on how the nrf mesh app adk works is impossible to follow and understand for a junior dev like me to make something close to a working app.
I might be...
Hei!
Mid code development my ability to flash new versions went away. The only clue I have is that W11 installed some new drivers, but I'm grasping at straws. I have screwed...
