Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
We are using public MAC that was purchased from IEEE (20 low bits are available for us to set and the upper 28 bits are constant to value assigned to us by the IEEE).
We...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.8.0 . I'm trying to get the data output (Bus...
Is it possible to override ZEPHYR_BASE when building with the nRF Connect extension in VS code?
I am using workflow 4 (application as manifest repository) and can build...
Hi DevZone.
We have problems with our NRF52833-DK We believe they are damaged because under normal conditions, they normally draw less current (.001 A). It is normal to...
Hello Nordic. I'm using the nRF9160DK and with it, some sensors and an sd-card. I save data to the sd-card using a fatfs filesystem, the files are of magnitude 500 kB. I want...
Is the button (from Thingy52 black case) the only option to trigger an IFTTT? Can I use the sensor's information to trigger an event with the IFTTT? like if the temperature...
Hi,
I am merging a PWM_driver example with a ble-peripheral-blinky example to generate PWM signals with user-defined arbitrary phase-shift and duty cycle.
I am done...
Hello,
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345).
My problem is regarding GPIO configurations are NOT retained ,when the nRF52832...
Dear Support term:
The Restful of Nrf Cloud is not work.
The node should have more that 100 data, so get ListMessages should give us pageNextToken.
Yes the result give...
Hi all,
I am using a custom board with NRF 52840 with SDK15.2 as slave and STM as master. I cannot receive right data, but the data to STM is right.
The above are...
Hi,
I am using an nRF52833dk to run a simple async SPI transceive API using k_poll My code is as below, for some reason it always returns BUS FAULT error Code:
Error...
Hello,
I face at least 2 problems and need some support.
What I want to achieve is that the DTM runs at our customer hardware for radio and later on BLE certification...
Hello !
In PS1.7 chapter 6.4.5 Encrypting packets on-the-fly in radio transmit mode is explained encryption of a short packets (MODE.LENGTH = Default).
But when MODE...
Hi there, I'm performing an throughput analysis using an nRF52 development board (BMD-350) and a Raspberry Pi 4B (Ubuntu 20.04, BlueZ 5.54) with an BLE 5.0 adapter. For measuring...
Hi,
I want to use the bsp button to our project, so I tested on the example "ble_app_blinky",
I modified the app button to bsp button, add two custom events to the bsp_event_t...
