Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I'm trying to do a 2 channels adc reading to read a value of a potentiometer and a value of a battery level. When I try to make it, I saw that sometimes, the value of...
Hello,
I have a problem with my nrf5340 in combination with the w5500. I have everything working but the connection is not stable.
I have nothing in the main.c
This...
Hello, Our company is developing a product class which uses a number of NRF devices. We want to set things up in such a way where there is a single "hub" device which uses...
Hi, guys.
My first link was here https://devzone.nordicsemi.com/f/nordic-q-a/84673/building-sample-v1-8-0-zephyr-samples-application_development-out_of_tree_driver-gives...
Hello!!!! I use libuart to carry out DTM test. I start DTM test use follow codes:
after the codes executed, when i send data to device use libuart, it receive nothing...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hello!
While looking at examples and trying to work on the nRF52832 with sdk 1.8.0 I am noticing there are varied uses of functions with and without the _dt at the end....
Case 1: Using nrf52832, solder bridge cut: what current values do the PPK gives : is it of the entire dev kit with all peripherals, programmer and BLE Soc or does it measure...
Hi, I'm attempting to migrate from SDK 14.2 to 15.2, and am encountering a problem with the crypto/rng module whilst trying to utilize micro_ecc.
(code being shown in order...
Soo,
I've had a sim and a device connected to the nrfcloud, it worked. Then I didn't use nrfcloud for a couple of months, and now it doesn't work anymore. It tries to connect...
I am using nrf52832 dev kit and soft device s132. I have use my board as peripheral
and i have another nrf52840 dev kit which i am using as a central connect it with my...
Hello,
I have to develop a new device that has to connect as a central device to three sensors, and has to connect as a peripheral to a smartphone. The type of connection...
Hi,
I'm observing a strange behavior with the UARTE peripherals on our nrf52840 based board when I'm trying to use a specific pin as TX.
In particular, I'm actually using...
Hello,
I've flashed to my custom nRF52832 board the ble_app_hrs_pca10040_s132 example, it works fine with iOS and Android hosts but when I try to connect to my development...
Hi Team
I have read https://devzone.nordicsemi.com/f/nordic-q-a/75801/request-tolerance-in-the-d-e-dimension-of-nrf52833-wlcsp . and https://devzone.nordicsemi.com/f/nordic...
