Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
I would like to set memory retention for system off with memory address and size of some retained struct. System off example has this for NRF52, but I'm not able to find clear...
I have an application with LESC. When I compile it for the 52840 I get the following RAM/Flash sizes with Oberon vs CC310:
CC310
Oberon
Flash
119820
...
Hello I am developing peripheral device with nRF52832. If you implement your own service and try to enable characteristic notify with nRFconnect, the following error notification...
Hello,
In my project i am currently creating a sub-module to read the battery voltage and convert that into percentage based on the ADC value read. I have refereed the guide...
Hello, Is it possible to add the remote provisioning functionality with the interactive PyAci serial library? We are developing a desktop application to do configuration and...
Hello.
It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm trying to characteristically add BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME and...
Hi!
I'm developing a small central BLE software, everything works well, please assume that I have correclty instantiated a connection, did the service and characteristic...
Hi,
I have looked around the internet and am trying to understand the ble security options. I cannot understand the correct approach to take for our application.
Our situation...
Hi,
How interrupt is working in nrf saac driver? I can see that it is already code is present in the adc_nrf_saac.c
static int init_saadc ( const struct device...
Hello,
I was wondering if it is possible to port older projects built using the now deprecated Nordic Thingy:52 SDK ( https://github.com/NordicSemiconductor/Nordic-Thingy52...
Hi,
As a university we bought several NRF51422 dongles to sniff BLE traffic
Following the installation instruction here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I am new in nordic previously I was working on Cypress controllers. I am trying to put the device in System ON Low power mode.
I have tried the below functions...
Hi,
I am working on a project using BT Mesh and I am evaluating a prototype using the nrf52840. I am not working with the mesh-SDK, because I am using zephyr. I am working...
Hi, I have a University group project which required us to build software on Android devices. Basically, this project requires us to build software based on BLE Mesh between...
Hello,
I want to communicate one card nrf5340dk with 2 same card in using 'central_uart' and 'peripheral_uart' samples.
I have succeeded to establish the connection and...
