Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
I have a simple prototype platform that previously uses nRF51822 which is discontinued. Now I plan to replace the BLE module with nRF52833.
Previously developed firmware...
Hi everyone ,
I want to perform DFU of SD+Bl+APP via UART.
I use nrfutil version 6.1.3.
The Softdevice is s140_nrf52_7.2.0_softdevice.hex and the application is based...
Hello everyone, i'm trying to deal with the ACS714T sensor but i can't find any samples or guide through internet the communication need to be done through ADC and SAADC HAL...
I am using the nrfx_uart and need to disable the receiption. I call nrfx_uart_rx_disable. When done once, the receiption is not working anymore, even when I call nrfx_uart_rx_enable...
I am the digital pcb and fw designer on a project using a dipole antenna defiend by the RF designer ( I have read the posts discouraging that and have taken that into account...
I am studying the ble_beacon example among the examples provided by nordic.
I want to code the beacon's uuid to indicate the mac address.
I studied to find the mac address...
Question: Can UART ASYNC and UART INTERRUPT work together? I want to use async UART along with interrupt driven USB CDC, but I am not able to use both together.
Details...
Hi team,
Note that nRF Sniffer already support nRF52840 dongle, but can that sniffer the BLE5 Advertising extension pack?
How to set the sniffer software?
Thanks!...
Hi,
I'm experimenting with the AoA locator receives IQ data on nRF52833 in ncs1.7.1. It worked well when the locator only received IQ data from one beacon. But when multiple...
Hiya. We're building a custom appliance on top of a Nordic chip that talks to an Android/iOS app developed with Flutter and a custom cross-platform Bluetooth plugin.
We...
Hi guys,
I tried to connect to nRF52832 using the app and it was successful. But when I directly use the BLE in the Android system(android 11) settings to connect to the...
Hi. I am new with nRF52 microcontrollers. I was able to create a project (myproject) in the examples folder and compile it with SEGGER embedded studio. I copied the whole...
Hello
I just downloaded nrf sdk 12.3 and am facing a problem straight away where I couldn't find valid answers that would fix my problems when searching this forum and on...
Hi,
The Bluetooth Core specification states that:
Per Bluetooth Core Specification Version 5.2 | Vol 6, Part F, Section 1.
The nRF5 SDK, v17.1.0, DTM Example states...
Hi,
I have a problem on two things
1. I want to advertise my custom 128bit UUID with ble appearance and manufacturer data but when i did my advertising device name become...
