Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hi,
I have two 52840DK,
OS : Windows10 X64
example: \ncs1.7.1\zephyr\samples\bluetooth\periodic_sync\
I didn't change the code, Whether I set [CONFIG_BT_LL_SW_SPLIT...
Hi,
nRF Conncet SDK1.7.1, Windows10 X64.
\ncs1.7.1\zephyr\samples\bluetooth\periodic_adv\,
building and debug work well,and i set the device name "PerAdv", then reload...
Hello
I'm trying to use the example code for ble_app_uart and it doesn't seem to work. I copied the folder for pca10028 and changed processor from nrf51422 to nrf51802 everywhere...
Hello,
I'm using a combination of B0 and MCU Boot.
I want to build MCU Boot for secondary slot to try upgrading it.
I pass CONFIG_BUILD_S1_VARIANT=y to the build system...
I am using four ADC inputs to the 9160.
I am driving each input from an op amp buffer as in the attached schematic.
ADC channels 0, 2, and 3 work as expected. As for channel...
I am trying to move our existing code based on the recommended NCS SDK. I was able to get MCU boot and SMP working, however, the update is extremely slow. I now seem to be...
I have developed a project using 9160. When I start up with the client board, the log will show that at command execution error occurs when I start up. Why is this? I admit...
Hello nRF community,
I am currently testing some Memfault application that comes with the nRF SDK v1.7.0. I have a custom board designed around the nRF9160 and have been...
Hey,
I'm developing and upgrading a BT mesh to Zephyr 2.7.99 and the base functions work, but my Node keep crashing and I don't know from where. It gives the following...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
Hi!
I want to use the function strptime from time.h to convert a timestamp to unix time but get the error "implicit declaration of function 'strptime'; did you mean 'strftime...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
Hi,
I am new to microwave board design, so I'd like a little advice please. I have attached photos of the 2.4ghz section of my board and would like to know if the component...
Hi,
I'm trying to integrate the secure_bootloader DFU code into the ble_app_uart_c example but am stuck on an error regarding not fitting in an 'UNPLACED_SECTIONS' region...
