hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
in sdk_config.h it says this
on page 24 of the nRF52832 datasheet, it seems that UART and UARTE cannot both be used (they share the same ID). Is this correct? effectively...
Hi,
We would like to connect other SIM card than iBasis's SIM card with nRF9160.
How can we register sim cards to nRF Cloud?
Can we register by inserting ICCID and PUK...
Greetings, I am developing an application for the NRF52840 in a RAK Wireless RAK4631, using the Arduino BlueFruit libraries.
When I monitor NRF_RTC1->COUNTER variable, it...
Hello everyone,
Because of problem with availability we were forced to change our ready-for-production project from nRF52832_xxAA to nRF52832_xxAB which has 2x less FLASH...
Hi, there
I am using nrf52832 chip on a custom hardware and also using softdevice 132 to send data to an app.
I need to send data from app to MCU and vice-versa and...
Hi
I am using the nRF52832DK and the BLE_App_Blinky.
I have a stable BLE connection to a phone and then I try to close the connection inside the nRF with sd_ble_gap_disconnect...
Hi, I am trying to implement Azure FOTA using your libraries. My source code is a combination of the Azure iot sample and the Azure fota sample + some necessary alterations...
As I know,the New Order Code of nRF52 Series has added Access port protection Controlled by hardware and software function, the earlier order code : Access port protection...
Hi, I'm working on updating nRF9160 modem firmware update.
I have update modem[mfw_nrf9160_1.3.1.zip] using nRF connect Desktop application and read partition using nRF...
Hi
I run nRF connect SDK 1.7.1 and have a custom nRF9160 board.
I'm trying to get the I2C peripheral to work with my own hardware.
I have read and googled all tutorials...
Hi,
Can I use the hex file compiled for nRF52810 for nRF52805 directly ? Please note that I am not using any peripherals other than radio.
Can I use the nRF52810 build...
We use the nRF24L01+ in a dedicated RX mode, and it is preceded by a power splitter, filters and LNA. In order to run some system calculations, I'd really like to know the...
