hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, I am trying to provision device using nRF mesh application. It discovers device and when i try to connect, it gives error device disconnected.
I tried this thing on...
Hi everyone, in special, Nordic; I'm facing a problem with the last two versions of the NRF CONNECT for Desktop (3.9.2/3) & the BitDefender Antivirus... I can download & install...
Hi everyone
I'm trying to generate the .hex file for examples like Tx and Rx or for my project but I'm not able to do that, please can anyone suggest me how can i do that...
I had been able to program my custom nRF52840 just fine until I wanted to change partitions. I erased everything and now am unable to communicate with the board at all. I...
https://github.com/NordicSemiconductor/pc-ble-driver-py/issues/210#issue-1089773469
I'm trying to build the project from sources. -using windows 10, python 3.8 -installed...
Port the radio_test sample to the Coprocessor sample to test the radio_test function error
How do I merge the two examples
I was hoping you could help me out
many...
Dear Sir.
We are using software based on mqtt simple project .
We added a 1 hz timer, Every 1 hz we toggle a led on and off.
Sometime the led is stuck on " on "...
Hi,
I'm trying to broadcast my BLE on my custom-made NRF51822 custom board.
My code was intended to run on Nrf51422, and it runs correctly on my PCA10028 DK with NRF514...
Hi,
we are working on nRF52832. my hardware is getting reset after a time. i don't know reset reason. my question is how to get cause of reset.
thank you
Hello,
I'm using the library LVGL on the board nRF9160 DK with an LCD screen.
In the lastest version of nRF Connect SDK (v.1.8.0), the version v7 is used for the library...
Hi,
The RAM Loading section for MCUboot states the following:
In case these drawbacks were acceptable, is it possible to run the image from external storage, without...
I'm trying to implement the full application for the nRF52832, while merging the Application, Mesh DFU Bootloader, SoftDevice and Device Page intelhexes into the one file...
Hi teams,
I noticed nRFConnect v3.9.0 is released.
After upgrading it, I got different errors as following, while detecting my nRF dongle & PPK during BLE app & Power...
I'm referring this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.2.0%2Flib_dfu_transport_ble.html
which states that when in bootloader...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
