hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
HI
I use SDK 17.0.0 in NRF52833.I test uart by example project ,the dir is \examples\peripheral\uart\pca10100\blank\arm5_no_packs .
Modify the baud to 921600 ,and send...
Hello,
I am attempting to update a custom C# application that is utilizing the NRFJPROG dll. We are hoping to add compatibility for multiple programmers connected to the...
We have developed a system using nRF52833 that is connected via WiFi to the cloud. We would like to do firmware update Over The Air from the Cloud using WiFi.
The first...
I used ble_app_hrs Demo to test bonding. However, I have been unable to bpnd successfully. I'll give you my bonding parameters.
#define SEC_PARAM_BOND 1
#define SEC_PARAM_MITM...
Hi,
When I increased FDS virtual pages to 50 pages and after download to device, and then used Programmer to read flash to get the images shows more longer than before,...
Hello,
I am a beginner in Zephyr, I am using the nRF 52840 DK board and I want to connect the HX711 module I have implemented nrfx_timer to make it possible to give pulse...
Hi,
I working on nrf52840 DK with nrf5 SDK17.
I tried to find out the power consumption of the peripheral(TWI/SPI) from the nrf52840 PS v1.7 document but it is not mentioned...
Hi,
I have combined a couple of examples in order to achieve the following on a custom nRF52810 board:
Count the number of pulses on a pin (using TIMER1)
Read the...
Hi, I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). Faced a problem related to the inability to connect to the MQTT broker when...
Hi
We want to run the AT command as the following, the response is always ERROR.
signal generator: CW, freq=param1-120KHz=1804.88MHz, power: -100dbm
AT%XRFTEST=4,1,3...
Hello
I need more flash and ram so I change the sdk to 13.1, but when I enabled the softdevice the log advice me use more ram.
How can I use little ram as s132_nrf52_4...
Hi,
Using the "mqtt_simple" example I found that the data_publish () function does not work for a timer handler.
In the case of the example below, when the data_publish...
Is there a way to lock NR9160 to a certain cell_id/eNB_id? I could not find any AT command for the job, but I assume that there must be a way to do it for testing purpose...
