I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
I've tested two scenarios using a hardware loopback to test UART functionality. The double buffer approach does not work as expected.
SDK version 1.6.1
CONFIG_SERIAL=y...
Hi,
I used nRF91DK for almost 2 months non stop to debug the final nRF91 based board for our air quality monitoring hardware to fight the propagation of Covid virus.
But...
I tested various copy methods in terms of instruction cycles, that I determined with DWT.
For that I copied an uint8_t array size 70 by
for Loop --> 63 Cycles
memcpy...
Hello,
I am using nRF52840 dev kit with sdk 17.0.2, s140 softdevice and dfu bootloader also implemented.
When I download the firmware to dev kit it works as intended...
Hi,
i am working on nRF52832. i am facing a issue of RESET when i call advertise_start() again after advertise duration. in debug it shows fatal error.
Hi there,
I've installed and followed the nRF Connect SDK manual install getting started guide ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
I'm using 52832 as a Central(SDK_17.0.2/S132_7.0.2), and sometimes get a connect-disconnect failure with reason 0x3e.It happens randomly and frequently.
I search the forum...
Hi Supportteam,
i am trying to use Release Assistance Indication (RAI) to shorten the RRC-Connected using nRF9160 DK.
I'm enabling REL14FEAT with the following AT commands...
Hello, sir.
I used to work on twi0 and twi1, but now I'd want to shift both twim0 and twim1. However, I'm getting an error saying that 'NRFX TWIM1 INST IDX' is undeclared...
Is it possible for nRF Connect iOS app to display devices that were connected/paired through the iOS Settings menu? The problem I am having is when looking to perform DFU...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
Right now I use the app_timer_cnt_get() method to get a current tick count. It appears to return a counter that increases with 32768 counts per second. However, it overflows...
Hi,
In NRF52832 i have integrated IMU sensor and and DPS sensor . i have build code and Run .
But after 2-3 minutes its stucked . so then i pressed the pause button ....
