Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am trying to setup a TWI interface between the nRF52 DK and the 16-bit ADC ADS1115 from TI. I am using the breakout board from Adafruit ( https://www.adafruit.com...
Hi,
I use nrf52832, SDK 16 and SD s132. I use FDS to store application data (fixed size), and I use bonding too. So the peer manager also store the peer related data in...
Hello,
I'm trying to implement a sleep mode for my application. Currently it has around 8 tasks.
I need to disable them all + disable some HW, such as GPS module. And...
Hello Nordic Team!
I'm working with the ble_app_hrs_c and a UART code I developed following the peripheral/uart example.
On the peripheral/uart example we have the following...
Hi,
I am using nordic52840 development kit board. and I am using sdk17.1 for development.
I tried to create .bin for secure bootloader code inside DFU. but the file...
hihih
I have DK9160 and THINGY91, which I bought 2 years ago.
I want to use them now.
I got the output:
***** Booting Zephyr OS build v1.14.99-ncs2-495-ga8933a2ead01...
Hi, I am using NRF9160 than I am using mqtt_simple example. I modified it. I want to send 4200 byte to mqtt broker but I get error. error is:<err> mqtt_simple: Publish failed...
Hello!
I have been working through examples lately trying to get the GPIO and PWM to work. But one issue I keep coming up to is how to define pins as input or output, and...
We have recently had a problem with the last programmer release (2.3.1). If we use an old version (2.2.0) we can plug our j-link edu and program our PCBs, if we use the last...
Hi,
We have a piece of code based on zephyr Driver to set up a double-edge GPIO interrupt. I set the interrupt flag to GPIO_INT_EDGE_BOTH. But it doesn't seem to trigger...
Hi,
I am using nrf52840 development kit with SDK 17.1.0.
I created a new project in IAR 8.50 and replicate project for sceure_bootloader in new project by adding files...
Hi!
We observe that our nRF91 SLM's get "softbricked" at random times, and a lot of them at the same time (We feel this is because of network unstability). These get stuck...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about the value of "ble_gap_evt_t::conn_handle".
I use central and peripheral. I have the following...
Dear nordic experts, when app_error_fault_handler() gets called, the firmware application hangs in an endless loop. While this is useful during development, it's a nightmare...
