Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello everybody,
I am working on a nRF52832 DK and implemented libuarte (on a nRF52832) to communicate with another uC on said board. I am using sdk 17.0.2. The goal is...
Hi.
I want to write an app for nRF Connect for Desktop, where i keep track of the RSSI of a specific device and plot in into a chart. I thougt about reusing some parts of...
Hi,
I would like to use MCK as a clock for adc CLK 4Mhz.
Could i enable & configure all registers without I2S or PDM peripheral activation?
Is there a sample code for...
we have an app where we use a nRF52-DK board (with the 52832 chip) as a serial to BLE interface. We connect to the board using the USB UART channel. The interface IC on the...
In NCS@ sdk_nrf/subsys/bluetooth/gatt_dm.c: bt_gatt_dm_start():
if bt_gatt_discover() return with an error, the variable "dm" shall be release by calling "svc_attr_memory_release...
Hi,
I followed the structure of ble_app_uart__saadc_timer_driven__scan_mode project and customize a program on the nRF52805. I transmit data through BLE to Nordic uart service...
I get build error "undefined reference to `bt_mesh_sensor_apparent_energy32'" if I try to add this sensor type.
Rest of my sensors are included but this one not (e.g. bt_mesh_sensor_apparent_power...
I'm trying toa custom nRF52840 board using SDK 17.02 and SD 7.01
I create a read/Write only service, it shows up in nRF Connect just fine
I can write to the service using...
Good day,
1. I am running the Asset Tracker v2 app on my nRF9160DK and I am monitoring the battery voltage and its time stamp from my nRF9160DK, as this data is transmitted...
In the Matter documentation, under the topic Building Matter - > Getting Help , the "Also see the quick start guide" link is broken. For me it gives:
NOT_FOUND: Requested...
Hello,
I am trying to use googleapis.com to perform cell and wifi geolocation and am having trouble connecting.
I am using a custom board with a nRF9160 chip and the 1...
In the below picture, it says Thingy 91 is certified for the bands given below.
Can you please confirm if this board is certified for AT&T , Verizon?
Regards ...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
