Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my phone.
My problem is that when I...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
Unlock is fine...
Last post regarding LE Audio was from 7 months ago and SDK for LE Audio wasn't available.
1) Is the SDK for LE Audio ready and available?
2) Is there any smartphone (Android...
Hello,
We have a dev project where one of the components is a device running on the nRF52DK, with NRF52382. The component is basically a UART to BLE interface, based on...
Dear,
We are trying to figure out the specification of write/read wear outs of the internal flash memory in nrf5340.
Would you please provide the specification to us...
Hi, when I try to build non secure boards several Kconfig errors provoke a Fatal error. I didn't have these type of errors until I updated to the 1.8.0 SDK, however the error...
Hello,
I have some real-time requirements needed to be implemented on RF transmitter project.
In the project files, app_timer2.c has already been included, and I have...
Hi everyone, I am looking into controlling servers using light_lightness server in 17.0.2
As far as I know, you can control the the publishing from client side by changing...
What is the easyest way to get all Nordic Thingy 91 data stored into a database? I could use Node-Red or whatever database, I need an easy procedure to follow.
Hello everyone. I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
Hi Everone..
I want to know for my project Which Example should i use for BLE mesh which support the OTA
I have nRF52832 DK, and several other custom board which is...
In my program, I want to supress all the Printk() statements conditionaly either from prj.conf or CMakeLists etc ? Or in simple terms, want to supress UART0 consol when required...
This is an old problem
first
what has changed in nrfjprog
# Flash the program flash: $(OUTPUT_DIRECTORY)/nrf51422_xxac.hex @echo Flashing: $< nrfjprog --program $< ...
Hi,
A new version of Segger Embedded Studio is available today: V 5.70a. Can I work with this version with the nRF Connect SDK or do I have to wait for a Nordic Edition...
