I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi, I am using the nrf52 Thread v4.1.0 SDK for development
I am using ADA4333
there pin 6 is used for Gate control but
in CLI pin 6 is used as uart tx
and it is hard...
I found the following problem with Programmer v2.0.1, using either a Nordic DK or a Segger J-Trace as the programming device (on Mac OS 11.6, and with nRF Connect 3.9.1):...
Dear All, I am trying to add the task watchdog to my application, but I am dealing with some interesting issues. The NRF SDK that I am using is the v1.6.1 I have dealt with...
Hey,
I saw the example in the SDK for hid keyboard over ble but it is only as a peripheral device.
In my project I have the nordic board as a central device connecting...
It has an iso_broadcast error, by GDB, it is in function ` bt_le_scan_start() ` where it throws an error. The error I cannot see through since the compiler option can't adjust...
Hello,
we developed a application on the nRF52840DK as a central device. Now we need to add four GPIO as inputs for reading the edges of four signals. Our problem is, that...
I have simple Bluetooth commination working. I can connect to nRF52840 with your nRF Toolbox on my Android. I can send a string from the nRF52840 to the Android app and have...
Hi,
I found this code for adafruit BNO055 sensor on GitHub which is a Arduino code.
https://github.com/adafruit/Adafruit_BNO055
How can I import this on the Nordic nRF5340...
Hi all, I'm searching for a SPI example with NCS 1.8, I'm currently using nrf52840dk_nrf52840. I've looking at the drivers (nrfx_spi) but I still don't get it at all, so I...
Hi, I have a Nordic Thingy 91. I need it to save battery and transmit sensor data to Nordic Cloud on PIR external interrupt (if I could count number of PIR pulses that would...
Hi I am testing the Thread examples
I worked on SIMPLE_COAP_EXAMPLE in nrf52840 DK there it works fine while opening UART and enter to CLI commands and its working
but...
Hi again Nordic. I'm trying to write sensor data to the external flash continuously as there is not enough RAM to hold all the data required. However, the writing operation...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
