I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my phone.
My problem is that when I...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
Unlock is fine...
Last post regarding LE Audio was from 7 months ago and SDK for LE Audio wasn't available.
1) Is the SDK for LE Audio ready and available?
2) Is there any smartphone (Android...
Hello,
We have a dev project where one of the components is a device running on the nRF52DK, with NRF52382. The component is basically a UART to BLE interface, based on...
Dear,
We are trying to figure out the specification of write/read wear outs of the internal flash memory in nrf5340.
Would you please provide the specification to us...
Hi, when I try to build non secure boards several Kconfig errors provoke a Fatal error. I didn't have these type of errors until I updated to the 1.8.0 SDK, however the error...
Hello,
I have some real-time requirements needed to be implemented on RF transmitter project.
In the project files, app_timer2.c has already been included, and I have...
Hi everyone, I am looking into controlling servers using light_lightness server in 17.0.2
As far as I know, you can control the the publishing from client side by changing...
What is the easyest way to get all Nordic Thingy 91 data stored into a database? I could use Node-Red or whatever database, I need an easy procedure to follow.
Hello everyone. I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
Hi Everone..
I want to know for my project Which Example should i use for BLE mesh which support the OTA
I have nRF52832 DK, and several other custom board which is...
In my program, I want to supress all the Printk() statements conditionaly either from prj.conf or CMakeLists etc ? Or in simple terms, want to supress UART0 consol when required...
This is an old problem
first
what has changed in nrfjprog
# Flash the program flash: $(OUTPUT_DIRECTORY)/nrf51422_xxac.hex @echo Flashing: $< nrfjprog --program $< ...
Hi,
A new version of Segger Embedded Studio is available today: V 5.70a. Can I work with this version with the nRF Connect SDK or do I have to wait for a Nordic Edition...
