Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
HI
I use SDK 17.0.0 in NRF52833.I test uart by example project ,the dir is \examples\peripheral\uart\pca10100\blank\arm5_no_packs .
Modify the baud to 921600 ,and send...
Hello,
I am attempting to update a custom C# application that is utilizing the NRFJPROG dll. We are hoping to add compatibility for multiple programmers connected to the...
We have developed a system using nRF52833 that is connected via WiFi to the cloud. We would like to do firmware update Over The Air from the Cloud using WiFi.
The first...
I used ble_app_hrs Demo to test bonding. However, I have been unable to bpnd successfully. I'll give you my bonding parameters.
#define SEC_PARAM_BOND 1
#define SEC_PARAM_MITM...
Hi,
When I increased FDS virtual pages to 50 pages and after download to device, and then used Programmer to read flash to get the images shows more longer than before,...
Hello,
I am a beginner in Zephyr, I am using the nRF 52840 DK board and I want to connect the HX711 module I have implemented nrfx_timer to make it possible to give pulse...
Hi,
I working on nrf52840 DK with nrf5 SDK17.
I tried to find out the power consumption of the peripheral(TWI/SPI) from the nrf52840 PS v1.7 document but it is not mentioned...
Hi,
I have combined a couple of examples in order to achieve the following on a custom nRF52810 board:
Count the number of pulses on a pin (using TIMER1)
Read the...
Hi, I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). Faced a problem related to the inability to connect to the MQTT broker when...
Hi
We want to run the AT command as the following, the response is always ERROR.
signal generator: CW, freq=param1-120KHz=1804.88MHz, power: -100dbm
AT%XRFTEST=4,1,3...
Hello
I need more flash and ram so I change the sdk to 13.1, but when I enabled the softdevice the log advice me use more ram.
How can I use little ram as s132_nrf52_4...
Hi,
Using the "mqtt_simple" example I found that the data_publish () function does not work for a timer handler.
In the case of the example below, when the data_publish...
Is there a way to lock NR9160 to a certain cell_id/eNB_id? I could not find any AT command for the job, but I assume that there must be a way to do it for testing purpose...
