Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
I am using ncs 1.5.2, and want to create a FOTA image. I am successfully able to build, flash and confirm the image, but am unable to set the version number of the image...
This is the errors , please help, to successfully create .hex file
If you want to look after full log details .......
Building firmware west build --build-dir c:\Users...
I bought a thingy91 module with ibasis scheduler on board. When I made the first installation of the mfw_nrf9160_1.3.1.zip software and the thingy91_asset_tracker_v2_ltem_2022...
I'm building a simple application using I2C to read sensor data (BNO055). I confirmed I2C and my sensor are all configured appropriately and working smoothly, but when I added...
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
Hi,
I am in the process of migration from SES to Visual Studio; I have imported my project; but it has no active build configuration. When I try and add a build configuration...
I am using 9160 to develop a watch product. During the network test, I found that the description of parameter period tau in CPSMS instruction and xmonitor instruction is...
So, i have created a custom board using the nrf52811 SoC. I tried to upload some bluetooth examples to it, and i can see the device on the nRF connect APP. The problem is...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
