Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear Nordic team,
For the security reason to be safe from the hacking, we like to completely disable the debugging and flashing port during production.
Would you please...
In nRF21540, two antenna ports are for antenna diversity. These two antennas are placed on the receiver side or one of them will act as transmitter and other as receiver?
Dear,
I followed the ticket below to set peripheral_lbs for nRF5340.
but still cannot see the 8uA in power consumption.Would you help?
I also use nRF5340DK and multi...
Board: nRF5340-DK
Version: NRF5340_xxAA_ENGD
SDK: 1.5.1, 1.6.1, etc
I have a Bluetooth project that also has quite a high SPI bandwidth requirement, so hence I am...
Hello Guys,
I am facing an issue with nrf52840 usb dongle.
I am using an external debugger J-Link for debugging the target ic.
During development, i have succesfully...
I am integrating flash storage example ( nRF5_SDK_17.0.2_d674dde\examples\peripheral\flash_fstorage) in ble_app_hrs_rscs_relay (nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral...
I am trying to implement bonded pairing with a project in which I already have NVS configured for user data. When implementing bonding, I understand that I need to remove...
The term advDelay is being used for the 0-10 ms random delay added to the fixed advertising interval. Since it is set by the link layer and can't be controlled by us, I want...
Hello,
I'm evaluating power optimization on nRF52. I'm using a Power Profiler Kit II and a nRF52-DK board.
I tried a lot of configuration and everything work as expected...
- The product I am making uses nRF52833. In addition, the audio part of Thingy 52 was added to the product as above. (The speaker uses 1.5W, 8ohm. Current consumption is about...
Hello,
I am trying to learn bluetooth using nrf52840 USB dongle. I have created an application from sample beacon and i would like to use I2C to implement my own driver...
unable to use time.h file
i have used:
#include time.h in main.c
added time.h file from C:\Keil_v5\ARM\ARMCC\include\time.h
when i use
time_t T = time(NULL); srand...
I have recently upgraded my working stack based on nrf sdk for thread and zigbee v2.0.0 to nrf sdk for thread and zigbee v4.0.0
But since then my mtd's are not getting commissioned...
We have built our application in nRF SDK for Thread and Zigbee. Since nRF SDK for Thread and Zigbee is in maintenance mode now, we plan to move our application to nRF Connect...
Hi,
I had my application based on nRF_SDK_For_Thread_and_Zigbee, and now I am porting my application to nRF_Connect_SDK.
When I use the nRF52840 DK board for testing...
