I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
Since the APP CPU memory is mapped at 0x2000.0000 in the perspective of the NET CPU, we understand that r/w access is possible for data. Is it possible for the NET CPU to...
I have a vendor model bt_mesh_model_op defined as follows
const struct bt_mesh_model_op _admin_model_ops [] = {
{ BT_MESH_MODEL_OP_3 ( OPCODE_SET_UNACK , VENDOR_ CID...
I modified the nrf9160 https_client sample to make a GET request to a web server and retrieve a JSON response. Unfortunately the rec_buf always ends up with an HTML response...
After several months of attempts, I was finally able to load, build, and flash the code from multi-NUS-master.zip using the VS version of nRF Connect, onto the nRF52840 DevKit...
Hello Nordic support team,
We are now creating a BLE central device which is part of a medical equipment.
The BLE communication works fine, but we want to add a BLE...
i'm writing a code for mic without using i2s because that mic will generate digital pdm signal.
i saw there is no solid code for low level driver or hard coding
Hello,
we need to SPI interface of a display controller RM6909 (AMOLED for smart watch) with the NRF52832 processor.
Could you please share us the source code for that...
Hi I want to set up a simple uarte communication between a NRF52832 and a faulhaber mcdc 3002s motion controller using the libuarte. I have max3232 logic converter in between...
Hello,
while migrating our FruityMesh framework to SDK17 I went through all SDK and SoftDevice release notes and migration documents and saw the following:
Now, to...
Hi Nordic Team,
Few questions about Power supply supervisor block of nRF52810. My device's supply volage (VDD) is 2 volt. I have enabled POFCON and the handler is getting...
Hello. I am designing an application where the goal is to send a notification, sleep for 1 second, send another etc.
To do this I used the application designed in this guide...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi,
I have a model_handler.c which builds fine, but the moment I change it to model_handler.cpp, I get build errors saying "duplicate descriptor is not allowed". I am struggling...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
