I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm having issues using the debugger on the nRF9160dk.
Here is the log that is output when I try to program the on-board 9160 with the command, nrfjprog --program <path_to...
Hello
I am trying to figure out the ram retention on my nRF52-DK using SES and SDK v17.1.0. I've run through the example ram_retention , and studied a topic in Nordic's...
Hi All,
My development IDE for BLE based firmware is Visual Studio Code.
SDK download for this version is 1.9.1 zephyr based.
I have select the example code "nrf/samples...
I'm using the nRF52832 with FreeRTOS and nRF5_SDK_17.0.2 on a custom board.
I am using a peripheral from a third party that uses Flash storage for certain parameters.
...
Hi Nordic,
I have 2 devices - nrf52840. One is Central and another is peripheral. I want to set a quicker data response time - shortest connection interval. As far as...
Hello,
as I see , many in DevZone have had a problem like this: we tried to merge twi-functionality into the basic ble_app_uart example. We set proper defines in sdk_config...
Hi,
we are developing a way to define through code a zigbee device composed of multiple endpoints, based on nRF5 SDK for Thread and Zigbee v4.1.0. The program can be flashed...
Hi all,
I'm trying to increase BLE throughput of ble_app_uart example (from official SDK16/ s132).
I've searched quite a few tutorials on which parameters should be...
Hi,
We need an detail description about uint32_t dev_config used in int i2c _configure ( const struct device * dev , uint32_t dev_config )
(zephyr i2c: https://docs...
Hello everyone.
I am beginner dev. I wanna run Serial Example Mesh and received data from BLE sensor. Can you support me complete this Project.
Thank you so much!
I'm testing a simple application based on the UDP/CoAP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi:
I want to use saadc peripheral,when i run the example "nRF5_SDK_17.0.2_d674dde\examples\peripheral\saadc",it worked well,but when I want to port this example to "nRF5_SDK_17...
https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/nrf_dm
I used the demo linked above to test RTT and DHCP respectively. Within two meters, I found that...
From the DF spec, we know that the connectionless AoA puts the CTE signal on the periodic synchronous adv, why, and what is the benefit. Is it possible to send CTE in extended...
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
