Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
Hello,
I am working with a nRF52833 and I am no longer able to use my JLink Base to flash it. I was previously able to flash it and there was no hardware change at all and...
Hello,
I am writing code in zephyr on nRF52840. I am advertising my BLE. and we have a stable android app (built-in a flutter). My problem is when I am trying to write an...
Hi teams,
Recently, during my test with some Arduino-Shield compatible daughter board with nRF52833DK, I found some pin mapping is incorrectly defined in nRF5 SDK.
The...
I have multiple elements with multiple sensors (4x6 in total, all 4 elements has the same type of sensors). I need to find out which element called sensor get callback. In...
Hello! I recently tried to develop Bluetooth communication based on nrf52840 chip. It is planned to implement a graphical software program on Windows platform. We checked...
My employer will be building a custom product in the next two weeks containing the NRF52840 module. We are using JLink debuggers in our test fixture to achieve this. We are...
Hi! The nRF52820 chip does not have the SAADC module used to estimate the battery life in its larger counterparts (nrf52840 and nrf52833). Is there a different way to estimate...
I'm trying to program the NFC Type 2 tag inside my Arduino Nano 33 BLE (nRF52840) following the nrfxlib 1.8.99 documentation , using the latest nRF Connect SDK. The nfc_t2t_setup...
Hi, I am using nrf52840 and Mesh V4.2.0 sensor and light_lightness examples.
I have been able to successfully combine the server side, but I have no idea how to start combining...
Hi, we stumbled into two issues when we enabled LESC in our application.
Relevant SDK config:
NRF_CRYPTO_ENABLED
NRF_CRYPTO_BACKEND_CC310_ENABLED
NRF_CRYPTO_BACKEND_CC310_RNG_ENABLED...
Hi,
I'm trying to enable PA/LNA control with a nRF5340 using the nRF Connect SDK v1.7.0. This version was the first to introduce FEM control, as described here: http://developer...
