Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm getting an error NRF_ERROR_NO_MEM when trying to initialize the LPS22HB, and the RTT log shows:
The line being triggered is in nrf_twi_sensor.c, line 151, which is...
I'm stuck with trying to install Nordic/ANT+ SoftDevice SS340-SD-v6.1.1 on the Adafruit Itsy Bitsy NRF52840. Within nRF Connect - Programmer, I am getting the following error...
Is it possible to use a NRF9160-SICA-B1 for a pcb designed around the NRF9160-SIAA-B1? Based on my findings, the pins are compatible, I just want to make sure I'm not missing...
My nRF52840-DK stopped working. When trying to connect using nRF Programmer v2.2.0 I get the following in the log:
15:45:05.011 Using @nordicsemiconductor/nrf-device-lib...
Hello,
just recived this kit, I ordered it some time ago but were no stock.
Problem is that software doesn't detect the hardware under "SELECT DEVICE". The device has...
When flashing files from an iOS device I run a lot into data size errors (not always), when using the same files on Android they can be copied without a problem.
It looks...
Hi,
I built a ble_app_buttonless_dfu_pca10040e_s112 project on the nRF52805. However, I cannot receive Bluetooth signal on nRF connect.
I have attached my generated hex...
Hi,
In an application with a nrf52840, we measure the frequency by counting rising edge with PPI linking GPIOTE EVENTS IN and TIMER TASK COUNT
GPIOTE.EVENTS_IN -> PPI...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
To the kind attention of Nordic support team,
we are planning to use nRF5_SDK_17.1.0_ddde560 and nRF52820 for a project. We are interested in using gzp gzll library compiled...
Hello
I'm working on a project inspired by the ble_thread_dyn_mtd_coap_cli example and for which I added the management of BLE LE Secure Connections (inspired by https:...
Hi all,
I observed an issue after upgrading to 1.8.0 and to Zephyr 2.7.0-ncs1 respectively. When having Zigbee (and NET core) enabled, all images are built as before. The...
Hello there,
I've set up 1.RaspberryPi with an otbr docker container.
Thanks to Sigurd I have set up 2.nRF21540DK running CoProcessor firmware built with nRF Connect SDK...
Hi,
I want to know more about composition data size. As I have read in Mesh Profile v1.0.1, composition data page 0 is mandatory, while the other pages are optional. The...
