My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
Hi,
I have the following 2 scenarios:
Scenario 1: I create an image with nrfutil containing SD, App and debug bootloader. I flash this image and it works. Then I change...
We have nrf5340pdk kit we are trying to flash code via nrf connect or Segger studio but firmware is not flash and when we powered up the pdk it's showing three port can you...
I'm using Visual Studio 1.7.1 on Windows 10 machine. With an nrf916DK.
I'm trying to learn about the shell and all seems to be working fine, based on what I've found in...
I'm trying to work with Kismet's nrf51822 plugin that would allow kismet to read the nRF BLE sniffer 4.1.0 the same way Wireshark does. Alas, theirs is C based and I don't...
Dear friend,
Based on the following conditions: SDK: 15.3 Target board: nRF52840-DK Example: \examples\ble_peripheral\ble_app_ancs_c ios version: 12.5.5 Do the following...
Hello,
I have successfully achieved the modem delta firmware update from mfw_nrf9160_1.2.7 to mfw_nrf9160_1.2.7-FOTA-TEST, vice-versa with sample code. But when it comes...
Dear support
Just started to learning following the tutorial here - https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-3-0#h769sk6kqovea15p99jn16lstat1dtpuuw...
Recently I purchased nRF9160 DK and I have a Vodafone Idea SIM (active). I followed the instructions precisely as per the Nordic infocenter but I am not able to connect my...
Hello
nRF52840 is easy to know pin number,
but nRF5340 no pin map,i can't read the pin diagram.
don't know where the pin corresponds to.
thanks
Best R...
Hi,
I managed to have the fat_fs sample to work.
Now i would like to be able to write and read files, onto the SD-CARD, that a PC will understand, it seems to needs...
Hello all,
I am developing on the nrf52 dk. and the following type definitions should be defined according to the given library.
Would somebody please comment if that...
