My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
We've upgraded our nRF9160 modem firmware and would like to downgrade to the pti_v1.1.x image so that we can test production test commands such as %XMIPIRFFEDBG. Where can...
Is there any info, which helps to distinguish between the versions of thingy 91 when ordering?
According https://www.nordicsemi.com/Products/Development-hardware/Nordic...
Hi Nordic Team,
I have a custom application running based on nRF NCS 1.5.0 with MCUboot enabled.
I'm having an issue where MCUboot simply doesn't jump to the application...
I had to reinstall Keil after running into some issues and lost most my packs. My project uses the NordicSemiconductor.nRF_DeviceFamilyPack.8.15.0 and the NordicSemiconductor...
I want to expose 2 endpoints on the nrf52840 DK - one is the existing Onboard LED and the other is the GPIO pin (P0.02) which I have enabled in overlay.
I am extending the...
Hello,
We are using A-GPS in our application to get faster TTFF and will be reading location coordinates after every 5 mins of duration. The application flow looks like...
Hello, On a custom board, using the NRF52832, we want to know the value of a potentiometer. This value is send via a signal on the AIN5 pin of the NRF52.
So, I tried to...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hello, guys.
I am using nRF Connect SDK, version 1.4.2 and nRF52840DK. I wonder what would be the way to print floating numbers during debug phase?
According to this thread...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
