Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
I'm trying to do a 2 channels adc reading to read a value of a potentiometer and a value of a battery level. When I try to make it, I saw that sometimes, the value of...
Hello,
I have a problem with my nrf5340 in combination with the w5500. I have everything working but the connection is not stable.
I have nothing in the main.c
This...
Hello, Our company is developing a product class which uses a number of NRF devices. We want to set things up in such a way where there is a single "hub" device which uses...
Hi, guys.
My first link was here https://devzone.nordicsemi.com/f/nordic-q-a/84673/building-sample-v1-8-0-zephyr-samples-application_development-out_of_tree_driver-gives...
Hello!!!! I use libuart to carry out DTM test. I start DTM test use follow codes:
after the codes executed, when i send data to device use libuart, it receive nothing...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hello!
While looking at examples and trying to work on the nRF52832 with sdk 1.8.0 I am noticing there are varied uses of functions with and without the _dt at the end....
Case 1: Using nrf52832, solder bridge cut: what current values do the PPK gives : is it of the entire dev kit with all peripherals, programmer and BLE Soc or does it measure...
Hi, I'm attempting to migrate from SDK 14.2 to 15.2, and am encountering a problem with the crypto/rng module whilst trying to utilize micro_ecc.
(code being shown in order...
Soo,
I've had a sim and a device connected to the nrfcloud, it worked. Then I didn't use nrfcloud for a couple of months, and now it doesn't work anymore. It tries to connect...
I am using nrf52832 dev kit and soft device s132. I have use my board as peripheral
and i have another nrf52840 dev kit which i am using as a central connect it with my...
Hello,
I have to develop a new device that has to connect as a central device to three sensors, and has to connect as a peripheral to a smartphone. The type of connection...
Hi,
I'm observing a strange behavior with the UARTE peripherals on our nrf52840 based board when I'm trying to use a specific pin as TX.
In particular, I'm actually using...
Hello,
I've flashed to my custom nRF52832 board the ble_app_hrs_pca10040_s132 example, it works fine with iOS and Android hosts but when I try to connect to my development...
Hi Team
I have read https://devzone.nordicsemi.com/f/nordic-q-a/75801/request-tolerance-in-the-d-e-dimension-of-nrf52833-wlcsp . and https://devzone.nordicsemi.com/f/nordic...
