NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I am new to developing hardware and software with BLE, and so far have had great success with using nrf52 modules. However, I would like to get a better understanding of it...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hello, I recently picked up a nRF PPK2 and I'm liking it a lot.
I have it wired in-line with a battery (1500mAh li-po) with my device under under test. Measuring battery...
Hi,
I am using nRF52805 to transmit string data to the mobile end app "nRF Connect".
I found that sometimes the app will display hex data instead of the expected decimal...
I'm using the logger (LOG_INF, LOG)_DBG...etc) to print out debug messages. I'd like to have timestamp printed out. Right now it looks like this: D: xxxx or I: xxxxx
I found...
Hello, I am working with 2 nRF52840 dk's and a Conbee ii.
The DK's are using nRF5 SDK for Thread and Zigbee 4.1.0.
DK 1 is running the CLI example.
DK 2 is running...
Hi, I want to integrate DWM3000 with with nrf9160. To begin with, I need a simple SPI example which I can't seem to find in the nRF connect SDK. There is an unofficial example...
I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). I'm trying to connect to a test mqtt broker (mosquitto) using AT commands via LTE...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hello,
I successfully merge example libuarte and ble_app_beacon and built .
My problem started after it receive 48 bytes of data from sensor via uart ,This is my area...
I want to enable GPIO IRQ in Trusted firmware-m 1.3 on nrf5340DK. I have TFM 1.3 which comes with zephyr v2.7.0 image flashed to board. followed the steps of https://www.trustedfirmware...
Hello,
I am trying to protect the battery on our application by putting my device in DEEP_SLEEP_! mode when a certain voltage is reached and waking it up upon a GPIO input...
Hello, i would like to know if this is possible to send less than 20bytes per packets, by changing the parameters like BLE_GATT_ATT_MTU_DEFAULT or the max data len. My goal...
Hello,
I'm trying to evaluate the Thingy:91 on Nb-IoT networks. I'm currently in the Philadelphia suburbs. I'm using the iBasis SIM card which was packaged with the device...
We like to use nrf9160 and we tried to find operator in India who sells NB-IoT / LTE-M sim card. but unable to find. Is there any operator providing NB-IoT / LTE-M enabled...
Dear Forum,
Im using a NRF52840dk connected to a NRF9160dk with the SLM application running.
Sending uart data from the 52840 to the modem works and modem gives a response...
