hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
HI
I use SDK 17.0.0 in NRF52833.I test uart by example project ,the dir is \examples\peripheral\uart\pca10100\blank\arm5_no_packs .
Modify the baud to 921600 ,and send...
Hello,
I am attempting to update a custom C# application that is utilizing the NRFJPROG dll. We are hoping to add compatibility for multiple programmers connected to the...
We have developed a system using nRF52833 that is connected via WiFi to the cloud. We would like to do firmware update Over The Air from the Cloud using WiFi.
The first...
I used ble_app_hrs Demo to test bonding. However, I have been unable to bpnd successfully. I'll give you my bonding parameters.
#define SEC_PARAM_BOND 1
#define SEC_PARAM_MITM...
Hi,
When I increased FDS virtual pages to 50 pages and after download to device, and then used Programmer to read flash to get the images shows more longer than before,...
Hello,
I am a beginner in Zephyr, I am using the nRF 52840 DK board and I want to connect the HX711 module I have implemented nrfx_timer to make it possible to give pulse...
Hi,
I working on nrf52840 DK with nrf5 SDK17.
I tried to find out the power consumption of the peripheral(TWI/SPI) from the nrf52840 PS v1.7 document but it is not mentioned...
Hi,
I have combined a couple of examples in order to achieve the following on a custom nRF52810 board:
Count the number of pulses on a pin (using TIMER1)
Read the...
Hi, I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). Faced a problem related to the inability to connect to the MQTT broker when...
Hi
We want to run the AT command as the following, the response is always ERROR.
signal generator: CW, freq=param1-120KHz=1804.88MHz, power: -100dbm
AT%XRFTEST=4,1,3...
Hello
I need more flash and ram so I change the sdk to 13.1, but when I enabled the softdevice the log advice me use more ram.
How can I use little ram as s132_nrf52_4...
Hi,
Using the "mqtt_simple" example I found that the data_publish () function does not work for a timer handler.
In the case of the example below, when the data_publish...
Is there a way to lock NR9160 to a certain cell_id/eNB_id? I could not find any AT command for the job, but I assume that there must be a way to do it for testing purpose...
