hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi there,
I am trying to enable the Read Back Protection in the software itself to avoid the FLASH, RAM etc. from being read with a debugger after being flashed for production...
Hello, I'd like to check what is the typical distance using 0 dBm tx power using Nrf52840?
I am using this BLE module based on Nordic, and it seems to work ONLY 2-3m far...
Hello
I am getting started with Nordic devices.
I recently bought a Thingy:91 and followed a tutorial to load the Asset Tracker application on to the device – this...
Dear,
We have been using QSPI external flash (MX25R64 installed at nrf5340 DK board) to write data. Particularly, when we ran flash_area_erase function ( located at zephyr...
Hello All,
How can I get my nRF52840's MAC address in Zephyr? Actually, I want to append the last 4 characters of the MAC address in CONFIG_BT_DEVICE_NAME.
So, when I...
Hello, we are developing a zephyr application on top of nrf52 soc. We can use the built-in zephyr drivers for most modules (ex: I2C, UART, nvm, etc.); however, for some modules...
I am really new at working with Bluetooth and the various protocols contained within.
I am using SDK 17.0 and drivers 2.7. I am working on a DK-52 board.
I am working...
The TWIM peripheral allows you to tx multiple buffers back-to-back like this:
- Set buffer 1 in TXD.PTR, TXD.AMOUNT - Trigger TASKS_STARTTX - Wait for EVENTS_TXSTARTED ...
Hi,
For testing purposes, I need a copy of the spec that the Nordic UART BLE service adheres to. Ex. minimum capabilities, mandatory functionality and attributes, etc. ...
Hello,
I tried enabling the Zigbee shell, through RTT, in my application and when that failed I built and burned the nrf/samples/zigbee instead, slightly modded to get rid...
Hi All. My task is simple. I want to implement LE secure connections on DFU. I have seen the ble_gls example. It has a passkey for bonding, I am looking into that too. I ran...
I have a repository that is intended to be used by other repositories via ZEPHYR_EXTRA_MODULES. This seems to be working fine. However, now I'm trying to add some code to...
I am evaluating a front end module by skyworks 66111 output power is ~14dBm. The FEM requires that logic dictate when to transmit and when to receive. When CRX, pin 17, is...
HI
we have developed our custom board using nrf5340. We are using NCS v1.7.1 for application development. I can't able to flash the HCI_rpmsg application to the network...
