hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi
I'm working with an nrf52840-dk on NCS 1.8.0.
I'm attempting to interface the board with an LS7366R quadrature counter over SPI; however, I'm not receiving any count...
hello Nordic
i am using ppk2 pca63100,
working on linux (manjaro), installed the nrfConnect v3.9.3 with power profiler v3.3.0
1. when i connect a device i have to...
This question relates to the unsatisfying reponse to ticket 283390.
The technology of the processor is not important. Arm Cortex processors are as fine as several others...
I am having trouble setting up a GPIO pin that will toggle when the radio is active on the network core. I have tried adding the code in bluetooth.c from the ppi_trace sample...
Hi everyone!
I am developing a board using a nrf52 as a BLE interface for an arduino. My idea in the future is update the firmware of the Nrf52 with OTA. But i wanna do...
Hello everyone. I am trying to set up a BLE central-peripheral network using nrf52840 based on NUS service. I need up to more than 10 peripherals which is customized board...
Hello there,
I'm trying to make a transceiver simulation on nRF24L01+ using Simulink. The block diagram provided in the documentation/datasheet was not clear enough for...
To create the prototype of a computer, which follows a non-von-Neumann-architecture, I am looking for an "Building Kit", which allows non-standard connections between computer...
Hi,
I'm trying to build my own "auto sleep" mechanism based on timers.
This is my code:
The timer works as expected, but when the soft_sleep function is reached, the...
We have a device that we are trying to implement an encrypted data transfer on. We wanted to lock down all the characteristics until we write a passkey on our security characteristic...
Hi there, I am trying to change the transmission power of the NRF5340 devices (for IEEE 802.15.4 radio) with Contiki-NG. With some other hardware (sky motes) that is based...
Hi, I am currently working on implement ble dfu on the nrf52840 dongle. I tried following this https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hi,
Using Power Profiler v3.3.0 with PPK2 on Chrome on MacOS.
The screenshot action results in a chopped image. See the top part is missing?
When I remove (by commenting...
Hi,
I'm trying to interface to a third-party 802.15.4 RF chip using an nRF52833, where the received packets from the remote device have enabled AES-CTR encryption.
I started...
Hello everyone,
I am looking at the init structure of the NRF52832's RTC and I cannot find any explanation on the "reliable" variable.
I can see its usage in the driver...
