hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello
I am planning to purchase Nordic Semiconductor Power Profiler Kit. Before purchasing the kit I need to know, Is this kit supports another company's microcontrollers...
I am using nrf52832 with a custom board with no external crystal oscillator. As bootloader I use "secure_bootloader_uart_mbr" so I don't have softdevice. SDK is 17.1.0_ddde560...
using ble_app_interactive on one dev kit and connecting to pc viewing on terminal
other is my perihperal.
on entering connect <device address> it gets disconnected
hi I sucessfully tested the blinky project on the nRF52840 dongle... btw i'm using vanilla zephyr...
but i'm unable to prototype the uart comm on this board... the board...
I'm working on NCS 1.8.0.
I can use DFU APIs to upgrade my firmware successfully, however, after DFU is finished and system reboot, the McuBoot to swap images is too slow...
Hi, I want to know brief aboout difference and objective of different types of Zephyr projects. When using nRF Connect SDK, in SES a project is created, 3 options are available...
Hello,
I am using the nRF52840 DK board and writing code in Zephyr and I want to change the clock frequency. Currently, I guess by default it is 32.768KHz How can I change...
Hi,
I am using an nRF9160/nRFConnect SDK 1.8.0/VSCode and my application uses MCUBoot and SPM. It is a "non secure" application.
I am trying to get a reset cause.
hwinfo_get_reset_cause...
I have read through similar posts, though none seem to talk directly about the DK and the JLink OB (SAM IC) missing bytes itself.
To start off with, I have created a basic...
Hello,
We are developing a product based on the nrf52840 chip with our own antenna design. we would like to register our product in SIG and obtain a company identifier ID...
Hi, can nRF52 DK or nRF 52832 read data from other sensors, for example, accelerometer, gyroscope and heart rate sensor. Accelerometer and gyroscope would have an implemented...
Hello.
I would like to know if its possible to preform a firmware update from the application itself like so:
1. Getting the firmware via UART in chunks of 2k (from a...
I am following along with the BLE DFU tutorial found here https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu but when I attempt to build...
Hi,
We have a custom board with the nrf5340 SoC, after erasing it with the erase function included in the nrf extension for VScode, we started getting the following error...
