Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I have an nRF52840 + nRF5 SDK 17.1.0 project that has been running on S140 7.2.0 and we're getting ready to lock some things in. But we happened to notice that there is a...
Hi,
I use peripheral_hr sample code of V1.7.1 version to send Data HRM by Bluetooth. the frequency is 22 Hz only.
I would like to icrease sample rate to 2 KHz, could i...
Screenshot of error message
Hello, I've followed the steps required on YouTube for setting up VS code with nrf Connect for desktop and the toolchain manager. It didn't...
Hi Team!
Currently I an working on disabling JTAG/Debug and SWD lines to protect code from read/write through any JTAG debugger.
For this, I have used nrfjprog utility...
Hi Support team,
I am testing nRF5340+nRF21540 with MT8852B now. I come across two issues in running the DTM FW from nRF Connect SDK v1.8.0:
1. nRF21540 TX gain value...
hi， I'm working on passthrough firmware(nRF5_SDK_17.1.0_ddde560)，I need to increase the priority of the serial port,see following code,When APP_UART_FIFO_INIT priority set...
Hello, in my zephyr application, I have uart1 configured as receive only using uarte at 921600 baud rate. Below is the description node:
I have a device sending a uart...
Hi,
We are using nRF52810 on a custom board, and when creating that board in NCS (in VScode), the Kconfig options are limited. We are not able to enable/disable the DCDC...
I have a project using NCS v1.8.0 where I enabled openthread.
For some reason, when trying to build `mbedtls/library/ecjpake.c`, the make command uses `-DMBEDTLS_CONFIG_FILE...
Hi! Im doing a SPI transaction using EGU and PPI. Software triggers the EGU, and PPI_CHANNEL_1 uses this event to start the SPIM transaction and set the CS pin low. PPI_CHANNEL_2...
I have followed the procedures to create a DFU package
- Using existing sample hex file "hrs_application_s132.hex"
1. nrfutil keys generate private.pem
2. nrfutil pkg...
I am using SDK V1.8 and have noticed that RTT output will run for a short time then stop.
Debug is still running because breakpoints can be set, just no printk output or...
Hi, guys.
I have been using NRF Connect SDK 1.8.0 , I want to use this
"v1.8.0\zephyr\samples\application_development\out_of_tree_driver"
to develop my custom driver...
Hi,
I'm developing a miniature application on nrf52805. I got an nrf52-dk and I am trying to understand which SDK i should use.
So far my problem is that on one hand ...
I'm trying to transition from Embedded Studio to VS Code. I have a sample application that I created in VS Code that builds without error, but when I start the debugger I...
