Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear Concern,
I want to keep my nRF52382 module in low power mode during non operational condition. During the TX and RX condition it has to wake up from the sleep mode...
Hi Team,
I tried the blinky example for the nRF52833 DK with the nRF5_SDK_17.1.0_ddde560 . I am using Segger Embedded studio for ARM V5.62 64bit – Non Commercial License...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The program is created by referring to the whitelist of "ble_app_hids_mouse" which...
1. in the file "Core_v5.2.pdf"
"The LE system operates in the 2.4 GHz ISM band at 2400-2483.5 MHz. The
LE system uses 40 RF channels. These RF channels have center frequencies...
1. I'm runnig the asset tracker fine with nRFCloud. When I run the cloud_client, I get this log:
*** Booting Zephyr OS build v2.7.0-ncs1 *** W: Already initialized. Nothing...
Hi,
Referring to this - https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/devicetree/bindings/net/wireless/nordic,nrf21540-fem.html I understand...
Hello everyone! I'd like to implement the nrf52-ble-image-transfer-demo with a nRF52840 Dongle, for a small low-power image transfer application. My question now is, how do...
Hello Nordic Experts,
Recently, I am using the nRF52840 dongle to sniff the Scannable Directed event, but I found that the AUX_SCAN_REQ cannot be sniffed, but the SCAN_REQ...
I am trying to use Visual Code environment (on macosx Intel macbook pro) to program nrf52840 dongle.
The dongle is found and programmed with using nRF Connect for Desktop...
Hi Nordic，
One of my customer has a problem about 2M phy.
They use 52840 connected with IOS via 2M phy.
They set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL both to 20...
Hi, I'm working on nRF9160 with Zephyr (SDK 1.7.1) and one SPI device. I analyze CS signal with correlation to SPI SCK. Is that normal that CS signal stays low much longer...
I am trying to add a Nordic Thingy 91 to my azure Iot hub.
i've configured the device according to the guide
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I noticed when using the UART BLE Example that there is no password or pairing request to connect to and use the device.
Everything works fine, and I even implemented my...
I followed the official tutorial. The programmer 2.3.3 in nRF Connect for Desktop v3.10.0 in Linux has problems programming the nRF52840 USB dongle rev 2.1.0 in DFU mode....
