Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, I am trying to provision device using nRF mesh application. It discovers device and when i try to connect, it gives error device disconnected.
I tried this thing on...
Hi everyone, in special, Nordic; I'm facing a problem with the last two versions of the NRF CONNECT for Desktop (3.9.2/3) & the BitDefender Antivirus... I can download & install...
Hi everyone
I'm trying to generate the .hex file for examples like Tx and Rx or for my project but I'm not able to do that, please can anyone suggest me how can i do that...
I had been able to program my custom nRF52840 just fine until I wanted to change partitions. I erased everything and now am unable to communicate with the board at all. I...
https://github.com/NordicSemiconductor/pc-ble-driver-py/issues/210#issue-1089773469
I'm trying to build the project from sources. -using windows 10, python 3.8 -installed...
Port the radio_test sample to the Coprocessor sample to test the radio_test function error
How do I merge the two examples
I was hoping you could help me out
many...
Dear Sir.
We are using software based on mqtt simple project .
We added a 1 hz timer, Every 1 hz we toggle a led on and off.
Sometime the led is stuck on " on "...
Hi,
I'm trying to broadcast my BLE on my custom-made NRF51822 custom board.
My code was intended to run on Nrf51422, and it runs correctly on my PCA10028 DK with NRF514...
Hi,
we are working on nRF52832. my hardware is getting reset after a time. i don't know reset reason. my question is how to get cause of reset.
thank you
Hello,
I'm using the library LVGL on the board nRF9160 DK with an LCD screen.
In the lastest version of nRF Connect SDK (v.1.8.0), the version v7 is used for the library...
Hi,
The RAM Loading section for MCUboot states the following:
In case these drawbacks were acceptable, is it possible to run the image from external storage, without...
I'm trying to implement the full application for the nRF52832, while merging the Application, Mesh DFU Bootloader, SoftDevice and Device Page intelhexes into the one file...
Hi teams,
I noticed nRFConnect v3.9.0 is released.
After upgrading it, I got different errors as following, while detecting my nRF dongle & PPK during BLE app & Power...
I'm referring this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.2.0%2Flib_dfu_transport_ble.html
which states that when in bootloader...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
