Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
So, this could just be an odd coincidence, but I'm stuck.
I had a project working using standard advertising. You connect, pair, and then the client (nRF Connect on Android...
Hi! I'm trying to encrypt some data using ECC 256 but I have some issues:
-I found a code ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/crypto...
Hello! I'm trying to use a custom SPM using this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
I closed the previous discussion by mistake: https://devzone.nordicsemi.com/f/nordic-q-a/83067/nrf9160-board-for-qr-code-project?ReplySortBy=CreatedDate&ReplySortOrder=Ascending...
Hi there
The project that I am focusing on was really time-critical, so I'm wondering whether we could disable Link Layer ACKs in nRF Connect SDK (i.e. Zephyr) ? If not...
We have been looking at InsightSIPs AoA Demo kit ( https://www.insightsip.com/products/bluetooth-smart-modules/isp1907 ) and are trying to understand the communication protocol...
Hi,
I would like to secure my application using security mode 1 level 3. LE Legacy pairing with OOB key sharing. (both master and slave device does not have I/O Capabilities...
Is there a way to access the data that comes into a provisioned node and is relayed on the mesh network, from the application layer in Zephyr?
I have a battery models erver...
Our product under development has tight flash requirements. As such, any optimisation to the build size of the product has a great affect on further development, therefore...
Hi Everyone,
I have seen some posts regarding this topic on the forum but would just like to clarify a few things.
I am currently using an application timer to sample...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
This issue exists in SDK 15.2 and earlier.
In nrf_log_frontend_dequeue() when memobj cannot be allocated, the backend flush api is used to free memory. However this memory...
Hi.
The VS code extension Cortex-Debug reports:
' WARNING: Cortex-Debug will deprecate use of GDB version 8. Please upgrade to version 9+ '
The manual installation...
