Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello I am implementing a battery voltage monitoring function using nrf52840. I am a beginner in hardware development. As the first step of this function, I am currently implementing...
Hi,
According to the Direction Finding White Paper , the CTE is a pure sin function at 2.4GHz. This is mixed with a local oscillator at 250KHz (for 1Mbps PHY) to obtain...
Hi,
I try to disable the reset mode and use the pin 0.18 as an normal input pin.
I'm using nrf52840 development kit (pca10056).
Does someone have i idea to resolve...
I currently have a nRF52832 DK connected to an external board with a BC832 module connected to the nRF52832 DK through a P19 connector. The voltage I have running and connections...
Hi everyone,
I'm currently trying to program my nRF52DK (nrf52382) to show it's battery voltage on the PuTTY emulator.
In order to run/simulate on the PuTTY emulator...
Hi,
I have working apps using custom BLE services on the 17.0 SDK
Now I need to write an app for the nRF5340 so the BLE softdevice can run in the network core
I have...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to conditionally switch the advertised UUID to another UUID. There is "sd_ble_uuid_vs_add...
Hello,
I have tested the USB HID Composite Example from Nordic SDK (15.0.0 and 17.1.0) on Windows and MacOS.
1) usbd_hid_composite_pca10056.hex from SDK15.0.0 works both...
I do not know how to use this site.
After my enquiry I received the following email and I am unable to reply to the answer.
> The ticket The input range of the SAADC...
I am trying to find where to implement secure communication between my BLE device (no display or input) and an Android tablet.
I am using the nRF_BLE library and am wondering...
Hi,
I've been browsing the forum here but didn't find an appropriate answer for my issue.
First, my platform & tools:
Programming nRF52833 (Laird BL653)
nRF5 SDK...
Hello,
I have been developing some products over the nRF51822 BLE. Got my introduction with nRF about 2 months back and despite the steep learning curve I was able to integrate...
Hi all. I'm using an old macbook and nRF Connect for Desktop just stuck at splash screen. Any version > 3.9.0 do not work.
System Version: macOS 10.13.6 (17G14042) Kernel...
Hello, I am using board nRF9160-dk (sdk 1.8.0). I need to get geolocation data using AGPS, for this I use the following sequence of AT commands:
AT%XSYSTEMMODE=1,0,1,0 AT...
