Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi, I use two nRF52840 DK for testing purposes for over 1.5 years now. Suddenly, yesterday the BLE module in one of the DK's stopped working. Just like that. Same functional...
Hellow
We are in trouble. Please tell me what to do.
The input range of the SAADC is not as expected.
I use: ・nrf52840 ・VDD=3.3V by Regulator ・nRF5_SDK_17.1.0 ・Sample...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
The example ble_app_uart is working fine (i.e. I get NRF_LOG_INFO from gatt_evt_handler), but my code doesn't. I've checked the diff between them and tried adding all diffs...
Hi All,
I am using nRF52 DK board & nRF5_SDK_17.1.0 for Development(Emulated Project for nRF52805), My application needs creation of multiple service and multiple characteristics...
I bought a handful of nrf52840-Dongle boards, with the intention of developing an application on one "dev" board and then flashing it through the Open Bootloader on the others...
hi am working on DFU- OTA on nRF52833. In one of the query I found the method for to evaluate DFU- OTA on nRf52833 , am able to do that ,after connected to the Bluetooth I...
Hello,
I am new to Nordic. Earlier I was using Cypress controllers CYBT343026-01. As per nRF documentation, I believe once the controller goes into a deep sleep mode, I...
Hello,
I am trying to port a project from the NRF52840 DK to a custom board where I am using the NRF52820. The code compiles fine when the project is using the settings...
Hi, devzone!
I'm trying to use a timer to periodically change the digital output but it seems that the handler function is not called.
The whole code is based on the...
Hello!
For a project, I am relying on RSSI data from the development kit nRF52832. The problem is that the data I get is in dBm (I assume?), that is values like -30, -50...
Hi,
We are designing a board that is controlled by a NRF52840 and that will use a NRF21540 (FEM) to enhance its radio link budget.
We will use the FEM with diversity antenna...
Hi,
The DFU(reuse ota code) partition configuration file I got from your technical support is as follows,It divides Flash（1024K） into the following regions：mcuboot(48K)...
Hi, I need to use UART0, UART1 and I2C0 in my application. I initialized these in overlay file (attached). When, debug is run, it is observed that the I2C binding is not successful...
