Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi everyone again,
We have a custom board using nrf52840. We upload a bootloader with J-Link. https://github.com/adafruit/Adafruit_nR ... 40_express But we have a problem...
I am working on a project, using nrf52840 as a BLE Center to connect to BLE HID devices, but every time the connection is automatically disconnected when the service is discovered...
I have implemented a Peripheral on an PCA10040 based on one of the SDK (v15) examples. When using nrf Connect with a nRF51 dongle I can connect to the peripheral and interact...
Hello !
1. Do you have examples for nRF52840 what is demonstrate encryption/decryption packets on the fly as it explained in PS chapter 6.4 ?
2. What about examples for...
I have a Jtrace which I use over ethernet.
Running nrfjprog shows:
nrfjprog -f nrf52 --eraseall ERROR: No debuggers were discovered. NOTE: For additional output, try running...
hello, im using nRF52840, pca10056, I was using the example ble uart from examples\peripheral\uart im planning on replacing the use of "putty" PC application with a program...
Hello, i did my own custom board with a nrf52805 and now I did one custom first she is working fine so I decided to do the same but I can't see my device in nrf connect app...
Based on the "system_off" example, I intend to use the RTC to wake the device up (a NRF52840) periodically every minute.
I setup the RTC with LFCLK (32KHz) to trigger a...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Hello,
I am trying UDP sample with a local SIM (Orange) to check eDRX settings following this ticket .
Carrier said i should set an APN. This was not needed with 1NCE...
I try the new save to CSV feature in v3.4 power profiler.
I try to save all, but it says 0MB.
The sample rate is 100ksps, and duration is 301 seconds, but would result...
hi all,
ST7735 driver for TFT Display which is tested using example/peripherals/GFX library, we want to test touch screen for this display ,the touch screen driver used...
Hi, I have the following code in main.c:
If I initialize the beacon advertising first, which is the shown configuration, I get fatal error code 8 out of ble_advertising_start...
I have recently updated the SDK for my application from version 13.0.0 to 17.1.0, everything seems to be in order except for this function in nrf_drv_twi.c called twi_clear_bus...
