I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I currently am working on a BLE device in which I am trying to set the Service and Characteristic UUIDs. Here is an example of what I mean:
As can be seen here, the Service...
Hi, I have developed a firmware in which I have added the custom service. My custom service UUID is showing 00001400-0000-0000-0000-00000000fff0 but I want only 0xFFF0. I...
Hi there,
I'm in the midst of migrating between SDK14.2->15.2, and SD 5.1->6.1
I'm calling sd_flash_write() and sd_flash_page_erase() before enabling the SoftDevice with...
Hi,
I start a new design using the nRF Connect Sdk instead of the nRF5 Mesh Sdk.
Is it possible to provision a device over the mesh network using the NCS (like the PB...
After LPN publishes message, NRF_MESH_EVT_LPN_FRIEND_POLL_COMPLETE event is generated five times. Also I noticed that instead of transmitting single publication message LPN...
Hi,
We have a problem with a nrf9160 connected in NB-IOT with a bad signal.
During the debugging session to try to figure out what happen, we saw that the mqtt_evt_handler...
Hi everyone,
I have a problem since a couple of day with an interrupt of app_timer not triggering when adding a BLE central to my project. The device is working well as...
If I can get time through WiFi then send it to the nRF5340 and place it in a Struct TM. is there any method to have the nRF5340 maintain the time/calendar from that initial...
I'm sorry. This must be trivial to all of you. I'm a beginner with nrf52 programming, and I saw several examples that refer to timers TASK_START, TASK_CLEAR, TASK_STOP. Everywhere...
Our device has both a 9160 and a 52840 on it.
The 9160 is running the stock serial modem firmware on it.
The 52840 is running a custom handler for AT connection targeted...
Hello,
We are doing some network quality tests on LTE-M with PSM off and notice loss on UDP between 0% to sometimes 15% on simple udp messages sent every 10 seconds from...
It is not very clean to start a work_q with no name when all others name them properly, or at least put in the name of their k_work_q struct. Working with system threads it...
Hi,
I'm upgrading my firmware from sdk1.7.0 and there is one error that i can't solve and need your help.
The code is working on SDK1.7.0, solved all the errors that appeared...
Hi,
I have a nrf5340 device which is built with nrf Connect SDK 1.6. I can successfully DFU over ble by nRF Connect mobile app. Right now, I am trying to do DFU from my...
Hello,
I am attempting to configure a project with full zephyr logs (using RTT backend). I am, however, unable to get the full logs (see example below):
[00013022] <dbg...
