I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I am in the process in getting the AWS version of the Asset Tracker v2 on my Thingy:91. I was having some issues with getting the cerificate but was able to get that...
I can not get the SPI Slave function working on nRF52840 (nrf52840dk_nrf52840 board). My goal is to have spi0 as master and spi1 as slave.
By linking the MISO en MOSI lines...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
I'm working on the 9160 SoC using nRF Connect SDK 1.8.0 to send MQTT messages to an AWS endpoint. The messages correctly are able to send and the device works for 5-10 minutes...
Using NordicSDK 1.6.1 and the following in the bt_le_adv_param and relevant settings in prj.conf
The secondary advertising data packet contains the advertiser address...
Hi all,
I am now using nrf52840DK and llpm example in nrf connect sdk 1.7.1.
Now I have three nrf52840DK, one as master ,and the others are slaves, they both use Latency...
Hello!
We are planning on using the nRF52832 DK together with an external antenna. We are highly interested in the readings being as accurate as possible, and we are wondering...
We are developing an application in which we need to modify an existing device driver. It's about LIS2DH driver that is part of nRF Connect SDK v1.8.0 and we are using VSCode...
Hi, we are using the nRF52 DK (nRF52832) to read data from the i2s bus and store it as a wave-file on the connected SD-Card. When pressing button 1 on the DK, recording starts...
(For some reason, I use "...' replace the original string) Here is the log for using AT to do HTTPS POST:
2022-02-07T12:19:39.057Z DEBUG modem >> AT#XHTTPCCON=1,"...",443...
Hi,
I'm working with NRF Connect SDK, and once in a while when I add new configuration options to the prj.conf, I get an error that some region overflowed by X bytes,...
Dear friend,
Since the customized nRF5340 board does not have an external 32.768KHz low-frequency crystal oscillator, the following is added to prj.conf in netboot:
The...
Hi
This is the first time I have tried to use the nrf52840 dongle and the programmer v2.3.1, it can see the dongle( com10), but as soon as I select Device tis is the response...
