We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello I am implementing a battery voltage monitoring function using nrf52840. I am a beginner in hardware development. As the first step of this function, I am currently implementing...
Hi,
According to the Direction Finding White Paper , the CTE is a pure sin function at 2.4GHz. This is mixed with a local oscillator at 250KHz (for 1Mbps PHY) to obtain...
Hi,
I try to disable the reset mode and use the pin 0.18 as an normal input pin.
I'm using nrf52840 development kit (pca10056).
Does someone have i idea to resolve...
I currently have a nRF52832 DK connected to an external board with a BC832 module connected to the nRF52832 DK through a P19 connector. The voltage I have running and connections...
Hi everyone,
I'm currently trying to program my nRF52DK (nrf52382) to show it's battery voltage on the PuTTY emulator.
In order to run/simulate on the PuTTY emulator...
Hi,
I have working apps using custom BLE services on the 17.0 SDK
Now I need to write an app for the nRF5340 so the BLE softdevice can run in the network core
I have...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to conditionally switch the advertised UUID to another UUID. There is "sd_ble_uuid_vs_add...
Hello,
I have tested the USB HID Composite Example from Nordic SDK (15.0.0 and 17.1.0) on Windows and MacOS.
1) usbd_hid_composite_pca10056.hex from SDK15.0.0 works both...
I do not know how to use this site.
After my enquiry I received the following email and I am unable to reply to the answer.
> The ticket The input range of the SAADC...
I am trying to find where to implement secure communication between my BLE device (no display or input) and an Android tablet.
I am using the nRF_BLE library and am wondering...
Hi,
I've been browsing the forum here but didn't find an appropriate answer for my issue.
First, my platform & tools:
Programming nRF52833 (Laird BL653)
nRF5 SDK...
Hello,
I have been developing some products over the nRF51822 BLE. Got my introduction with nRF about 2 months back and despite the steep learning curve I was able to integrate...
Hi all. I'm using an old macbook and nRF Connect for Desktop just stuck at splash screen. Any version > 3.9.0 do not work.
System Version: macOS 10.13.6 (17G14042) Kernel...
Hello, I am using board nRF9160-dk (sdk 1.8.0). I need to get geolocation data using AGPS, for this I use the following sequence of AT commands:
AT%XSYSTEMMODE=1,0,1,0 AT...
